Custom Cycle Parts with Attitude, Made in the US of A!


MidPac w/ STD Build, Chrome Hardware, Smooth Lid








MidPac








MidPac w/ Reverse Build, 2K Urethane Primer, Smooth Lid, Matte Black hardware

MidPac Trimline Motorcycle Trunk - Our MidPac is 100% hand made in our shop by us. From waxing the molds that we designed and built, spraying gelcoat to 40 mils, spraying neutral gel & polyester resin to another 80 mils, hand laying and pressing 50 square feet of 1.5 oz fiberglass mat, installing OSB in the lower layers of the bottom for strength, laying additional reinforcements in the hinge, latch, and top areas, cutting & trimming, sanding, fitting, painting and/or buffing, hand drilling and fitting all 100+ pieces of hardware, laying interior carpet, and finally assembling these units...all a very tedious labor of love.

Dimensions... Our MidPac is a unique height/thickness, designed to suit riders who want a little more storage space and a bit taller passenger backrest, while retaining a sleek and sexy stance. Our MidPac is 8-1/2" thick in the back, and about 10" thick in the front. It is about 11" thick in the front center, behind the backrest. It has the same bottom footprint as the standard full size pack, which is approx. 23" wide, 17.5" front-to-back. It's about 1/2 way between the thickness of our ChoptPac and our KingPac. All MidPacs are built with our new bottom design to allow for speaker lid clearance and fit all years of bikes.

What makes us different? Unlike most everything else on the market that is plastic, ABS, or heavy Chopper Gun fiberglass, the MidPac we manufacture is all hand laid and pressed glass, OSB reinforced flat bottom (no need for the H-D bottom plate inside). These aren't the cookie cutter plastic stuff seen everywhere, they are each built to order for the customer, with the specific options and featured you want. We also do a lot of "one off" pieces for people, so don't be afraid to ask if you have a special request!

It comes fitted and built! All 100+ pieces of hardware are drilled, fitted, and installed. Hinges/locks, lid seal, lanyard, latches, etc. All the hard work is done for you, unlike most of the other packs out there that come to you as a box full of parts to figure out. It also has an extended rain drip to help keep water out. It doesn't need the metal reinforcement plate in the bottom like H-D and all the plastic trunks under various names from China. We use locking latches with the locks built-in, no need for separate hole in the trunk for a lock. The hinges are our own design and a significant inrovement over HD latches, with welded hinge pins and an improved hinge footprint for better load distribution. We build our own rubberized lid restraint with a stainless steel interior for a rattle-free lid stay.

Primer or Color? We can fabricate this in Red Oxide or 2K Urethane primer for painting for $450, and Vivid Black gelcoat for $500. Color match is available, but we recommend you have that done by a local painter who can actually see your bike and perfectly match it to your bike. If you don't have a local painter for your color matching, we can take care of you. We pay the shipping to you, if you live in the USA.

Options available are:
- We have two different lid styles. Our "Classic Lid" has the depression in the center, seen on most factory HD packs. Our new "Smooth Lid" has a nice, smooth contour and is also a great choice if you plan to install speakers through the lid of your pack. Lid style is your choice and is no extra cost to you.

- Interior carpet package, Typically $50 installed in the bottom, $80 for the top and bottom. Most people only do the lower section.

- Reverse build: Uniquely available only from us. Latches on LH side, hinges on RH side, great for big wheel bikes with centerstand and trikes, you step off the bike on the left and open the pack without having to walk around the bike as with a std HD setup. Since those bikes don't lean to the left, a reverse build is a great option at no extra cost.

- Chrome, flat black, or gloss black hardware (hinges, latches, screws) = No extra cost

- Down-n-Dirty custom backrest from HighRollers MC Seats = $175.

- The new Mustang backrest available = $150

- The Mustang backrest w/extended armrests = $260

- It is compatible with the H-D backrests, in the event you have or prefer one.

We don't build the bottom mount, but we can point you at some very cost effective choices used by many of our customers.

We typically prefer to deal with our MidPac customers on a one-on-one basis, to get every detail of our custom fabrication and assembly of these perfect. Email us at sales@621cycles.com to discuss your needs, and be sure to check out daily build pictures and loads of customer installations on our facebook page at: facebook.com/621cycles .








...RETURN to the 621 Cycles Homepage...